Key Takeaways
- China has world-class CNC capabilities. From simple brackets to complex 5-axis parts — you can find it all.
- Savings are real but vary. 40-70% cheaper than Western shops, depending on complexity and volume.
- Tolerance capability varies widely. Not all Chinese shops can hold tight tolerances consistently — verify with test parts.
- Quality depends on the shop, not the country. There are excellent shops and terrible shops — choose carefully.
- DFM is critical for cost. Design features that are easy to machine can cut cost dramatically.
- Start with prototypes. Test a shop’s quality with small orders before committing to production.
1. Introduction: CNC Machining — The Precision Workhorse of Manufacturing
CNC (Computer Numerical Control) machining is the process of using computer-controlled machine tools to remove material from a solid block (billet) to create a finished part. It is one of the most versatile and precise manufacturing processes available, capable of producing parts with extremely tight tolerances and complex geometries.
For hardware companies, CNC machining serves several critical roles:
- Prototyping: Fast production of functional prototypes from CAD files
- Low-volume production: Cost-effective for parts needed in quantities from 1 to 1,000 units
- High-precision parts: Components that require tight tolerances that other processes cannot achieve
- Tooling and fixtures: Molds, jigs, and fixtures for other manufacturing processes
- Post-processing: Secondary operations on cast, molded, or stamped parts
China has one of the largest and most competitive CNC machining industries in the world. From small job shops with a few mills to large factories with hundreds of CNC machines, the country offers an enormous range of capabilities at prices significantly below Western benchmarks.
However, the quality of CNC machining in China varies enormously. At the top end, you find world-class precision shops serving aerospace, medical, and semiconductor industries. At the bottom end, you find shops with old machines, poorly trained operators, and minimal quality control — producing parts that may look right but fail inspection.
He Qianggao, a senior lawyer at Geason Law Offices with over 10 years of experience in Chinese manufacturing (license 14403201310092337), has seen both sides: “We had a medical device client who needed precision parts with ±0.01mm tolerances. They found a Chinese shop online that quoted 70% less than their US supplier. The first batch came back looking fine, but when measured, half the parts were out of tolerance. The shop had quoted based on ‘standard tolerance’ and never confirmed they could meet the tight specs. A proper technical review and test part before production would have saved everyone time and money.”
This guide covers CNC machining in China — the key processes, capabilities, materials, cost factors, quality considerations, and how to find and work with good machine shops. Whether you need prototypes, low-volume production, or high-precision components, this guide will help you navigate China’s CNC machining landscape.
2. CNC Machining Processes Available in China
2.1 CNC Milling
CNC milling uses rotating cutting tools to remove material from a stationary workpiece. It is the most common CNC machining process.
3-axis milling:
- Most common type of CNC milling
- Tool moves in X, Y, and Z axes
- Can machine features on the top, bottom, and sides of a part (with re-fixturing)
- Pros: Most widely available, lowest cost, fastest for simple parts
- Limitations: Cannot easily machine undercuts or complex 3D surfaces in one setup
- Typical accuracy: ±0.05-0.1mm
4-axis milling:
- Adds a rotary axis (A-axis) to 3-axis milling
- Can rotate the part to machine features on multiple sides in one setup
- Pros: Can machine features around a cylindrical part, reduces setups
- Used for: Shafts, camshafts, turbine blades, parts with features at different angles
- Typical accuracy: ±0.05-0.15mm (rotary axis adds some error)
5-axis milling:
- Adds two more rotary axes (A and B, or B and C)
- Tool can approach the workpiece from any direction
- Can machine very complex 3D shapes in a single setup
- Pros: Complex geometries, fewer setups, better surface finish on complex surfaces
- Cons: More expensive, requires more skilled programming and operation
- Used for: Aerospace components, turbine blades, mold tooling, complex medical parts
- Typical accuracy: ±0.02-0.08mm (depends on machine quality)
2.2 CNC Turning
CNC turning uses a rotating workpiece and a stationary cutting tool. Used for parts with rotational symmetry.
Standard turning:
- External turning, facing, boring, threading, grooving
- Pros: Very fast for round parts, excellent surface finish, tight tolerances on diameters
- Used for: Shafts, pins, bushings, fasteners, fittings
- Typical diameter tolerance: ±0.01-0.03mm
Swiss turning (Swiss-type automatic lathe):
- Specialized turning for small, long, slender parts
- Part slides through a guide bushing for support
- Very high precision and productivity for small parts
- Used for: Medical components, watch parts, connector pins, small shafts
- Typical accuracy: ±0.005-0.02mm
Turn-mill centers:
- Combined turning and milling in one machine
- Can machine both rotational and non-rotational features in a single setup
- Pros: Reduces setups, improves accuracy (all features machined in one setup)
- Used for: Complex parts that need both turning and milling
2.3 Grinding
Grinding uses an abrasive wheel to remove material. Used for high precision and fine surface finishes.
| Type of Grinding | Purpose | Typical Accuracy |
|---|---|---|
| Surface grinding | Flat surfaces, precise thickness | ±0.005mm flatness, Ra 0.2-0.8 μm |
| Cylindrical grinding (OD/ID) | Round external and internal surfaces | ±0.002-0.005mm diameter, Ra 0.1-0.4 μm |
| Centerless grinding | Cylindrical parts without centers | ±0.003-0.01mm diameter |
| Jig grinding | Precise holes and features | ±0.002-0.005mm |
| Honing | Internal bore finishing | Very fine surface finish, precise size |
Grinding is used when tolerances are too tight or surface finish is too fine for milling or turning. It is also used for hard materials that are difficult to machine with standard tools.
2.4 EDM (Electrical Discharge Machining)
EDM uses electrical sparks to erode material. Used for very hard materials and complex shapes that are difficult to machine with cutting tools.
Wire EDM:
- Uses a thin wire (typically brass or molybdenum, 0.1-0.3mm diameter) as the electrode
- Cuts through the workpiece along a programmed path
- Pros: Very precise, can cut complex shapes, no cutting force (good for delicate parts), works on any conductive material regardless of hardness
- Cons: Slow, limited to shapes the wire can reach (no undercuts), creates a recast layer
- Used for: Punch and die components, complex 2D shapes, hard materials, precision slots
- Typical accuracy: ±0.003-0.01mm
Sinker EDM (Ram EDM):
- Uses a shaped electrode (usually graphite or copper) to create a cavity
- Electrode shape is the negative of the desired cavity
- Pros: Can create complex internal cavities, very fine details, works on hard materials
- Cons: Slow, electrode wear requires compensation, surface finish depends on power settings
- Used for: Mold cavities, die making, complex internal features
- Typical accuracy: ±0.005-0.02mm
2.5 Other Processes
Broaching: For keyways, splines, and internal shapes — uses a toothed tool pulled through a hole Hobbing: For gears and splines — uses a rotating hob cutter Laser cutting: For sheet metal and flat patterns (see sheet metal guide) Waterjet cutting: For cutting flat shapes in any material
3. Materials
Virtually any material that can be cut with a cutting tool can be CNC machined in China.
3.1 Metals
| Material | Common Grades | Properties | Typical Uses | Machinability |
|---|---|---|---|---|
| Aluminum | 6061, 7075, 2024, 5052 | Lightweight, good strength, excellent machinability | Enclosures, brackets, heat sinks, prototypes | Excellent |
| Carbon steel | 1018, 1045, 4140, 4340 | Good strength, low cost, good machinability | Structural parts, shafts, gears, fixtures | Good |
| Stainless steel | 304, 316, 17-4PH | Corrosion resistance, hygienic | Medical, food, marine, chemical | Fair (gummy, work-hardens) |
| Tool steel | D2, A2, H13, S7 | Very hard, wear-resistant | Dies, molds, cutting tools | Poor (hard, abrasive) |
| Brass/copper | C360, C110 | Excellent conductivity, corrosion resistance | Electrical, plumbing, decorative | Excellent |
| Titanium | Ti-6Al-4V, Grade 2 | High strength-to-weight, corrosion resistance | Medical, aerospace, marine | Poor (low thermal conductivity) |
| Stellite/Inconel | Stellite 6, Inconel 718 | High temperature, corrosion resistance | Aerospace, energy, valves | Very poor |
3.2 Plastics
- Acrylic (PMMA): Clear, rigid, brittle — optical parts, enclosures
- POM/Delrin (Acetal): Good wear resistance, low friction — gears, bearings
- Nylon (PA): Tough, good wear resistance — gears, bushings, structural parts
- PEEK: High performance, high temperature — medical, aerospace, industrial
- UHMW: Very low friction, wear resistant — bearings, guides
- Polycarbonate (PC): Impact resistant, transparent — protective covers, lenses
3.3 Composites and Other Materials
- Carbon fiber/FRP: High strength-to-weight — aerospace, automotive, sporting goods
- G10/FR4: Glass-reinforced epoxy — electrical insulation, structural
- Foam (PU, EPS): Low density — patterns, prototypes, packaging
4. Design for Manufacturability (DFM) for CNC Machining
Good DFM can reduce CNC machining cost by 30-50% while improving quality. Here are the key guidelines.
4.1 Milling DFM
Internal corners:
- Internal corners always have a radius (end mills are round)
- Use the largest possible corner radius — smaller tools are slower and break more easily
- Guideline: internal corner radius ≥ 1/4 of the pocket depth (minimum 1mm)
Pocket depth:
- Deep, narrow pockets are difficult and slow to machine
- Guideline: pocket depth ≤ 4x pocket width (preferably ≤ 3x)
- Deeper pockets require longer tools, which deflect and cause inaccuracy
Holes:
- Standard drill sizes are cheaper than custom sizes
- Depth-to-diameter ratio: ≤ 3x is easy, 3-6x is moderate, >6x is deep hole drilling (more expensive)
- Countersinks and counterbores add cost but are often necessary
Tolerances:
- Only specify tight tolerances on critical dimensions
- General tolerance: ±0.1mm is usually fine for non-critical features
- Tight tolerance (±0.02mm or better) requires more careful machining and inspection → higher cost
- Very tight tolerances (±0.005mm or better) usually require grinding → much higher cost
Setup reduction:
- Minimize the number of sides that need machining
- Each setup adds time and cost
- Design parts so features can be machined in as few setups as possible
4.2 Turning DFM
- Avoid very long, thin parts — they deflect during machining, reducing accuracy and surface finish
- Use standard diameters when possible — standard tools are cheaper and more available
- Consider minimum bore diameter and depth — deep, narrow holes are difficult to bore
- Threads: Use standard thread sizes; specify thread depth carefully (partial threads at the bottom of blind holes)
4.3 General DFM Tips
- Minimize setups. Each side or orientation adds setup time and cost.
- Use standard tools. Custom or unusual tool sizes cost more and may not be available.
- Avoid very small features. Micro-features require special tools and slower feeds.
- Specify realistic tolerances. Tighter tolerances = higher cost. Only tighten what is necessary.
- Consider material. Hard materials are slower to machine. Exotic materials cost more and are harder to find.
- Design for fixturing. Think about how the part will be held during machining. Do you have flat surfaces for clamping?
- Provide complete CAD files. 3D models (STEP, IGES) plus 2D drawings with dimensions and tolerances.
5. Quality Considerations
5.1 Common Quality Issues
Dimensional issues:
- Features out of tolerance (too big, too small, wrong position)
- Poor flatness, parallelism, or perpendicularity
- Thread quality issues (wrong pitch, wrong depth, burrs)
Surface quality:
- Poor surface finish (too rough, tool marks, chatter marks)
- Scratches and dents from handling
- Burrs on edges and holes (not properly deburred)
- Discoloration from heat or coolant
Material issues:
- Wrong material or alloy
- Material with defects (inclusions, porosity)
- Material certification does not match actual material
Process issues:
- Wrong tool or wrong feeds/speeds leading to poor quality
- Workholding problems causing part movement
- Programming errors
- Measurement errors during inspection
5.2 How to Ensure Quality
Clear documentation:
- Complete 2D drawings with all dimensions and tolerances
- 3D CAD file (STEP or IGES format)
- Material specification with grade and condition
- Finish requirements (surface roughness, coating, plating)
- Any special requirements (deburring, cleaning, packaging)
First article inspection (FAI):
- Always inspect the first part from a new job before the shop runs the full order
- Check all critical dimensions
- Verify material with a test certificate or independent analysis
- For critical parts, do a full dimensional report
- Approve the first article before proceeding
In-process inspection:
- For larger orders, inspect parts periodically during production
- Check key dimensions to make sure the process is stable
- Catch issues early before many bad parts are made
Final inspection:
- 100% inspection for critical dimensions on critical parts
- AQL sampling for general quality on larger orders
- Dimensional inspection with CMM or calibrated tools
- Surface finish inspection
Inspection equipment to look for in a shop:
- CMM (Coordinate Measuring Machine) — for 3D dimensional inspection
- Calipers, micrometers, height gauges — basic dimensional tools (all should be calibrated)
- Surface roughness tester — for Ra measurements
- Optical comparator — for 2D profile measurement
- Hardness tester — for verifying material hardness
- Spectrometer — for material composition verification
6. Cost Factors
6.1 What Drives CNC Machining Cost
| Cost Factor | Impact |
|---|---|
| Material cost | 10-50% of total (depends on material and part size) |
| Machine time | Largest cost component — set by machine type and cycle time |
| Setup time | Each setup adds cost — proportional to part complexity |
| Number of setups | Each side/operation adds setup time |
| Tolerance requirements | Tighter tolerances = slower machining + more inspection = higher cost |
| Surface finish | Finer finishes require slower feeds and finer tools |
| Part complexity | Complex 3D shapes take longer to program and machine |
| Quantity | Setup time is amortized over more parts → lower per-unit cost |
| Material machinability | Hard or gummy materials take longer to machine |
| Quality inspection | More inspection requirements add cost |
6.2 Typical Machine Hourly Rates in China (2026)
| Machine Type | Hourly Rate (USD) |
|---|---|
| 3-axis CNC mill (small) | $20-40 |
| 3-axis CNC mill (large) | $35-60 |
| 4-axis CNC mill | $40-70 |
| 5-axis CNC mill | $60-120 |
| CNC lathe | $15-35 |
| Swiss turning | $25-50 |
| Turn-mill center | $50-90 |
| Surface grinding | $20-40 |
| Cylindrical grinding | $30-60 |
| Wire EDM | $25-50 |
| Sinker EDM | $30-60 |
These are approximate rates for mid-tier shops in China. Premium shops with tighter tolerances and better quality charge more. Very low-end shops may charge less but deliver lower quality.
6.3 Cost Reduction Tips
- Increase quantity. Higher volume amortizes setup time over more parts.
- Simplify the design. Reduce features, increase tolerances where possible.
- Use standard materials. Exotic materials are expensive and may have long lead times.
- Minimize setups. Design parts to be machined in fewer orientations.
- Optimize tolerances. Only specify tight tolerances on critical dimensions.
- Consider alternative processes. For high volume, casting, forging, or stamping may be cheaper than machining from solid.
- Consolidate parts. Can two machined parts be combined into one?
- Choose the right shop. Match the shop’s capability to your needs — you do not need a 5-axis aerospace shop for simple aluminum brackets.
7. Finding and Working with CNC Shops in China
7.1 Types of CNC Shops
- Prototype/job shops: Small, flexible, good for low-volume and prototypes. Usually have a mix of equipment.
- Production shops: Focus on medium-to-high volume production. More automated, better process control.
- Precision shops: Specialize in tight tolerances and complex parts. Higher cost, higher quality.
- Specialty shops: Focus on specific processes (grinding, EDM, Swiss turning) or specific industries (medical, aerospace, automotive).
- Full-service manufacturers: Offer CNC machining plus finishing, assembly, testing, and supply chain management.
7.2 Where to Find CNC Shops
- Shenzhen/Dongguan: Highest concentration of CNC shops, especially for prototypes, consumer electronics, and small-to-medium parts.
- Suzhou/Wuxi: Strong in precision machining, automotive, and industrial parts.
- Ningbo: Good for medium-to-high volume, automotive components.
- Online platforms: Alibaba, Made-in-China, RapidDirect, Xometry (but quality varies).
- Referrals: Best way to find quality shops. Ask other hardware founders and engineers.
7.3 Evaluating CNC Shops
Facility and equipment:
- What machines do they have? (Brand, age, condition)
- Brands like Mazak, DMG Mori, Haas, Makino indicate higher quality
- How many machines? Are they well-maintained?
- Do they have inspection equipment (CMM, etc.)?
- Is the shop clean and organized?
Capabilities:
- What materials do they typically machine?
- What industries do they serve?
- What is their typical part size and complexity?
- What tolerances can they consistently hold?
- Do they have in-house engineering and programming?
Quality systems:
- ISO 9001 certification
- Inspection procedures and records
- How do they handle non-conforming parts?
- Do they provide first article inspection reports?
- Calibration records for measurement equipment
Communication:
- Do they have English-speaking staff?
- How fast do they respond?
- Do they ask good questions and provide DFM feedback?
- Do they understand your requirements?
7.4 The Test Part Approach
Before committing to a large order, always test a shop with a smaller order:
- Send a representative part — one that is typical of the work you will be doing
- Evaluate:
- Quality: Do parts meet specifications? Measure them yourself.
- Communication: Were they responsive? Did they ask questions?
- Delivery: Did they deliver on time?
- Documentation: Did they provide proper inspection reports?
- Problem-solving: How did they handle any issues that came up?
- If they pass the test, move to larger orders gradually.
- If they fail, find another shop. Do not waste time trying to fix a bad supplier.
8. Key Takeaways
CNC machining is a versatile and precise manufacturing process — and China offers some of the best value in the world for CNC machined parts. But quality varies enormously, so choosing the right shop is critical.
Core principles:
- China has every level of CNC capability. From basic job shops to precision aerospace shops — you can find what you need.
- Quality is not guaranteed by location. There are excellent shops and terrible shops. Evaluate each individually.
- Start with a test part. Always test a new shop with a representative part before committing to production.
- DFM saves money. Small design changes can dramatically reduce machining cost and improve quality.
- Tolerances drive cost. Only specify tight tolerances where you need them. General tolerances are fine for most features.
- Clear documentation prevents errors. Complete drawings, 3D models, and material specs are essential.
- Inspection is your responsibility. Do not assume the shop has inspected parts properly. Verify critical dimensions yourself or use a third party.
At Geason Law Offices, we help foreign hardware companies navigate Chinese manufacturing — from supplier qualification to quality agreements to dispute resolution. He Qianggao and our manufacturing team bring over a decade of experience to help you find the right suppliers, negotiate fair terms, and protect your interests.
FAQ
Q1: How do I protect my IP when manufacturing in China?
A1: Protecting IP in Chinese manufacturing requires a multi-layered approach: registering trademarks, patents, and copyrights in China (not just in your home country), executing comprehensive manufacturing agreements with clear IP ownership provisions and confidentiality clauses, implementing supply chain controls to prevent overproduction and gray market diversion, conducting regular factory audits, and registering IP with China Customs to prevent unauthorized exports. It’s also important to conduct thorough due diligence on manufacturing partners and to structure agreements with clear dispute resolution mechanisms, preferably with Chinese court jurisdiction or arbitration in China.
Q2: What are the key labor law requirements for manufacturing facilities in China?
A2: Manufacturing facilities in China must comply with comprehensive labor requirements including standard working hours (40 hours/week), overtime pay (150% on weekdays, 200% on rest days, 300% on statutory holidays), mandatory social insurance contributions (pension, medical, unemployment, work injury, maternity), written employment contracts within 30 days of hiring, and workplace safety standards under the Work Safety Law. For factories using dispatch workers, the total proportion of dispatched workers cannot exceed 10% of the total workforce.
Q3: How does China’s environmental regulation affect manufacturing operations?
A3: China’s environmental regulations have become increasingly stringent, particularly under the Environmental Protection Law and the “Dual Carbon” goals. Manufacturing facilities must obtain environmental impact assessments (EIA) before construction, install pollution control equipment, meet emission standards, and participate in the emissions trading system for certain pollutants. Violation penalties have increased significantly and can include daily fines, production suspensions, and even criminal liability for serious environmental pollution incidents.
Q4: What quality control standards apply to manufactured goods in China?
A4: China has a comprehensive system of quality standards including national standards (GB), industry standards, local standards, and enterprise standards. For many consumer products, compliance with GB standards is mandatory. Products sold in China may also require CCC (China Compulsory Certification) marking depending on the product category. For export products, manufacturers must meet the standards of the destination country. China’s Product Quality Law establishes manufacturer liability for defective products, including compensation for damages caused by quality issues.
Q5: What is the difference between OEM and ODM arrangements in China?
A5: OEM (Original Equipment Manufacturing) involves a foreign brand providing product specifications and designs to a Chinese factory that manufactures according to those exact specifications. ODM (Original Design Manufacturing) involves the Chinese factory both designing and manufacturing the product, with the foreign brand typically putting its own label on the finished product. The key legal differences relate to intellectual property ownership, liability for design defects, and the degree of control the brand has over the manufacturing process and quality standards.
Further Reading
- Sheet Metal Fabrication in China: Processes, Materials, and Quality Considerations — Sheet metal
- Casting Processes in China: Die Casting, Investment Casting, Sand Casting Compared — Casting
- Quality Control in China Hardware: Inspection, Testing and Defect Prevention — Quality control
- Surface Treatment & Finishing Processes in China: A Guide for Hardware Products — Surface finishing
Next Steps
Whether you need prototypes, low-volume production, or high-precision components, China’s CNC machining industry can deliver excellent value — if you find the right shop.
Two service lines most relevant for CNC machining and manufacturing:
- Commercial Contracts & Manufacturing Agreements — Quality and specification clauses
- Manufacturing Legal Support in China — Full manufacturing legal support
To discuss CNC machining or any manufacturing legal matter, Contact Geason Law Offices. The initial consultation is free; the form prepares an email in your own mail application.
Related guides in this series
- Injection Molding in China: A Complete Guide for Hardware Startups
- Rapid Prototyping in China: A Guide for Hardware Startups
- Should-Cost Analysis & Value Engineering: Optimizing Manufacturing Costs in China
Frequently Asked Questions↑ Back to article
What types of CNC machining services are available in China?
China has comprehensive CNC machining capabilities, including: (1) CNC milling — 3-axis, 4-axis, and 5-axis for complex 3D shapes, (2) CNC turning — for rotational parts, shafts, bushings, (3) CNC turning-milling centers — combined milling and turning in one setup, (4) Grinding — surface grinding, cylindrical grinding, ID/OD grinding for high precision and fine finishes, (5) Wire EDM — for complex shapes in hard materials, very tight tolerances, (6) Sinker EDM — for cavities and deep features, (7) Swiss turning — for small, high-precision parts like pins and connectors. Most shops offer milling and turning; more advanced shops offer multi-axis and EDM.
How much does CNC machining cost in China compared to the US or Europe?
CNC machining in China is typically 40-70% cheaper than in the US or Europe. The exact savings depend on part complexity, material, and tolerance requirements. Simple milled parts: $20-50/hour machine rate in China vs. $80-150/hour in the US. Complex 5-axis or precision grinding: $50-120/hour in China vs. $120-250/hour in the US. However, shipping, import duties, and communication overhead reduce the savings — so for very small or simple parts, the total cost difference may be less dramatic.
What tolerances can Chinese CNC shops hold?
Tolerance capability depends on the shop's equipment, skill level, and quality control. A good CNC shop in China can typically hold: General milling: ±0.05mm (±0.002 inch). Precision milling: ±0.02mm (±0.001 inch). Turning: ±0.01-0.03mm diameter. Grinding: ±0.005mm (0.0002 inch) or better. Wire EDM: ±0.003-0.01mm. Very high precision (micron-level) is available at specialized shops, usually with grinding or lapping processes. Always specify your tolerance requirements and verify the shop can meet them — not all Chinese shops can hold tight tolerances consistently.
What materials can be CNC machined in China?
Virtually any material that can be cut with a cutting tool: (1) Metals — aluminum (6061, 7075), steel (1018, 4140, 4340), stainless steel (304, 316, 17-4PH), brass, copper, titanium, tool steel, (2) Plastics — acrylic, POM/Delrin, nylon, PEEK, UHMW, PC, (3) Composites — carbon fiber, G10/FR4, (4) Foam — for prototypes and patterns. China has excellent material supply chains, so most materials are readily available. Exotic materials (Inconel, titanium alloys, engineering plastics) may have longer lead times or require specific suppliers.
How do I find a good CNC machine shop in China?
To find a good CNC shop: (1) Start with referrals from other hardware companies — the best shops are busy and get work through word of mouth, (2) Look for shops that specialize in your type of work (high-volume vs. prototype, simple vs. complex, specific materials), (3) Send a test part first — give them a challenging but representative part to evaluate their quality, communication, and delivery, (4) Visit the shop if possible — see their equipment, cleanliness, and quality control firsthand, (5) Check for certifications like ISO 9001 and relevant industry standards, (6) Ask about their equipment — newer, well-maintained machines produce better parts, (7) Evaluate their engineering support — good shops provide DFM feedback and catch issues before machining.
How does DFM reduce CNC machining costs?
Design for Manufacturing (DFM) reduces CNC machining costs by eliminating features that are difficult, time-consuming, or impossible to machine. Simple design changes like using standard drill sizes, adding corner radii instead of sharp internal corners, reducing depth-to-diameter ratios, avoiding thin walls or features, and using standard tolerances where possible can dramatically reduce machining time and tool wear. Good DFM can reduce part cost by 10-40% while also improving quality and consistency, and most reputable Chinese CNC shops provide DFM feedback as part of their quotation process.
What quality control measures should a good Chinese CNC shop have?
A good CNC shop should have a formal quality management system (preferably ISO 9001 certified), first article inspection (FAI) for every new part, in-process inspection at key stages, final dimensional inspection with calibrated measuring equipment like CMMs, material traceability documentation, and clear non-conformance handling procedures. They should also provide inspection reports with each shipment. For high-precision parts, look for shops with dedicated QC departments and advanced metrology equipment, not just calipers and micrometers.