Key Takeaways
- Die casting for high volume, non-ferrous. Fastest, most accurate, lowest per-unit cost at volume — but only for aluminum, zinc, magnesium.
- Investment casting for complex, high-melting. Best for complex geometries and ferrous metals — more expensive but very precise.
- Sand casting for large, low volume. Cheapest tooling, can make huge parts, widest material range — but lowest precision.
- Tooling cost vs. part cost trade-off. Higher tooling cost = lower per-part cost. Choose based on your volume.
- Porosity is the #1 quality concern. Cast parts have inherent porosity — manage it with good design and process control.
- China has foundries for every need. From tiny zinc die castings to massive sand castings — China has it all.
1. Introduction: Casting — The Foundation of Metal Parts Manufacturing
Casting is one of humanity’s oldest manufacturing processes — and still one of the most important. From tiny zinc electronic components to massive steel ship propellers, casting creates metal parts of all sizes, shapes, and materials. For hardware products, castings are used for structural parts, enclosures, heat sinks, gears, brackets, and countless other components.
China is the world’s largest casting producer — accounting for nearly half of global casting output. The country has tens of thousands of foundries producing everything from high-precision die castings for consumer electronics to massive castings for heavy industry. Chinese foundries offer competitive pricing, short lead times, and a wide range of capabilities.
However, not all foundries are equal. Quality varies enormously — from world-class facilities with automated lines and strict quality control to small backyard foundries with minimal process control. Choosing the right casting process and the right foundry is critical to getting good parts at a fair price.
He Qianggao, a senior lawyer at Geason Law Offices with over 10 years of experience in Chinese manufacturing (license 14403201310092337), has seen his share of casting disputes: “We had a client who ordered aluminum die cast heat sinks from a Chinese foundry. The parts looked fine on the surface, but when they tested thermal performance, it was 30% worse than expected. The cause? The foundry had cut corners by using more recycled material than specified, resulting in higher porosity and lower thermal conductivity. The contract only specified ‘ADC12 aluminum’ without defining composition limits or quality requirements. A proper material specification and testing requirement would have prevented the problem.”
This guide compares the major casting processes available in China — die casting, investment casting, and sand casting — along with several other methods. It covers how each process works, what materials are available, cost considerations, quality issues, and how to choose the right process for your part.
2. Die Casting
Die casting is the most widely used casting process for high-volume metal parts, especially in consumer electronics, automotive, and appliances.
2.1 How Die Casting Works
- A steel mold (die) is machined into the shape of the desired part
- Molten metal (usually aluminum or zinc) is injected into the die under high pressure
- The metal solidifies quickly (seconds to minutes)
- The die opens and the part is ejected
- The part is trimmed of flash and any gates or runners
Types of die casting machines:
- Hot chamber machines: For zinc, magnesium, and other low-melting-point alloys. The injection mechanism is submerged in molten metal. Faster cycle times.
- Cold chamber machines: For aluminum and other higher-melting-point alloys. Molten metal is poured into the chamber for each shot. Slower but handles higher temperatures.
2.2 Die Casting Materials
| Material | Common Alloys | Properties | Typical Uses |
|---|---|---|---|
| Aluminum | ADC12, A380, A356, AlSi9Cu3 | Lightweight, good strength, good corrosion resistance, excellent thermal conductivity | Enclosures, heat sinks, brackets, automotive parts, consumer electronics |
| Zinc | Zamak 3, Zamak 5, Zamak 7 | Very good castability, excellent detail and surface finish, good impact strength | Small parts, decorative hardware, connectors, zippers, toys |
| Magnesium | AZ91D, AM60B | Ultra-lightweight, good strength-to-weight, good EMI/RFI shielding | Thin-wall enclosures, laptop frames, automotive parts |
| Copper/Brass | Various | Excellent conductivity, corrosion resistance, antimicrobial | Plumbing fittings, electrical connectors, gears |
2.3 Die Casting Advantages and Disadvantages
| Advantages | Disadvantages |
|---|---|
| Very high production rate (fast cycle times) | High tooling cost |
| Excellent dimensional accuracy and repeatability | Only for non-ferrous metals (aluminum, zinc, magnesium) |
| Good surface finish | Not suitable for low volume |
| Can produce thin walls and complex details | Part design limited by die geometry (undercuts need slides) |
| Low per-unit cost at high volume | Porosity can be an issue |
| Highly automated, consistent quality | Limited part size (usually under 50kg for aluminum) |
2.4 Typical Specifications
| Parameter | Typical Range |
|---|---|
| Minimum wall thickness | 0.5-1.0mm (aluminum), 0.3mm (zinc) |
| Dimensional tolerance | ±0.05mm for small features, ±0.1-0.3% overall |
| Surface finish (as-cast) | Ra 1.6-6.3 μm |
| Part size range | A few grams up to ~50kg (aluminum) |
| Tooling cost | $3,000-50,000+ (depends on size and complexity) |
| Tooling lead time | 3-8 weeks |
| Production rate | 100-10,000+ parts per day |
| Minimum order quantity | 1,000-5,000 parts typically (tooling cost needs to be amortized) |
2.5 Die Casting in China
China has an enormous die casting industry, particularly concentrated in:
- Guangdong (Shenzhen, Dongguan, Foshan): Consumer electronics die casting, aluminum and zinc
- Zhejiang (Ningbo, Wenzhou): Automotive and industrial die casting
- Jiangsu (Suzhou, Wuxi): Precision die casting, automotive
Die casting quality in China ranges from world-class to very basic. High-end foundries serving global automotive and electronics brands have automated machines, real-time process monitoring, and strict quality control. Lower-tier foundries may use older machines and have minimal process control.
When selecting a die casting supplier, look for:
- Modern, well-maintained die casting machines
- In-house tool making capability
- CNC machining capability for secondary operations
- Quality control (CMM, X-ray for porosity, spectrometer for material composition)
- Relevant industry experience (automotive, electronics, etc.)
3. Investment Casting (Lost Wax Casting)
Investment casting, also known as lost wax casting, is a precision casting process that produces parts with excellent dimensional accuracy and surface finish. It can handle complex geometries and a wide range of metals.
3.1 How Investment Casting Works
- A wax pattern of the part is injection molded
- Multiple wax patterns are assembled onto a wax sprue tree
- The tree is dipped in ceramic slurry and coated with sand (stucco) — repeated several times to build a thick shell
- The wax is melted out of the ceramic shell (hence “lost wax”)
- The ceramic shell is fired to strengthen it and burn out any remaining wax
- Molten metal is poured into the hot shell
- After cooling, the ceramic shell is broken away to reveal the cast parts
- Parts are cut from the sprue and finished
3.2 Investment Casting Materials
Investment casting can handle almost any metal that can be melted:
- Stainless steel: 304, 316, 17-4PH — very common
- Carbon steel and alloy steel: 4140, 4340, etc.
- Aluminum: Less common (die casting is usually cheaper for aluminum)
- Copper alloys: Brass, bronze, copper
- Superalloys: Inconel, Hastelloy, cobalt alloys — for high-temperature applications
- Precious metals: Gold, silver — for jewelry
3.3 Investment Casting Advantages and Disadvantages
| Advantages | Disadvantages |
|---|---|
| Excellent dimensional accuracy and surface finish | More expensive per part than die casting |
| Can produce very complex geometries | Slower process, longer lead times |
| Wide range of metals (including steel) | Higher tooling cost than sand casting |
| Almost no draft angle needed | Size limitation — typically under 50kg |
| Minimal machining required | Not suitable for very high volume |
| Can make parts with internal passages | Labor-intensive process |
3.4 Typical Specifications
| Parameter | Typical Range |
|---|---|
| Minimum wall thickness | 1.0-1.5mm |
| Dimensional tolerance | ±0.05mm for small parts, ±0.1-0.2mm overall |
| Surface finish (as-cast) | Ra 1.6-3.2 μm (very good for casting) |
| Part size range | A few grams up to ~50kg (can be larger but rare) |
| Tooling cost (wax die) | $1,500-15,000 |
| Tooling lead time | 2-4 weeks |
| Production rate | 50-500 parts per week (depending on size/complexity) |
| Minimum order quantity | 50-500 parts |
3.5 Investment Casting in China
China is a major center for investment casting, with foundries serving global aerospace, automotive, medical, and industrial markets. Key regions:
- Shandong and Jiangsu: Steel investment casting for industrial and automotive
- Zhejiang: Precision investment casting for hardware and machinery
- Guangdong: Investment casting for consumer products and electronics
Investment casting in China is generally very cost-competitive compared to Western foundries — often 40-60% lower cost for comparable quality.
4. Sand Casting
Sand casting is the oldest and most widely used casting process. It uses sand molds to form metal parts. Sand casting is extremely versatile — it can make parts from a few grams to hundreds of tons, in almost any metal.
4.1 How Sand Casting Works
- A pattern (positive model of the part) is made from wood, plastic, or metal
- The pattern is placed in a box (flask) and sand is packed around it
- The pattern is removed, leaving a cavity in the sand
- A core is placed in the mold if internal cavities are needed
- The two halves of the mold are closed
- Molten metal is poured into the mold cavity
- After the metal solidifies, the sand is broken away to remove the casting
- The part is cleaned, trimmed, and inspected
Types of sand casting:
- Green sand: Most common, uses sand mixed with clay and water. Low cost.
- Resin-bonded sand: Uses resin binder for higher strength and better surface finish.
- Shell molding: Uses a thin shell of resin-coated sand. Good accuracy and surface finish.
- Lost foam: Uses a foam pattern that vaporizes when metal is poured. Good for complex shapes.
4.2 Sand Casting Materials
Sand casting works with virtually any metal:
- Gray iron, ductile iron: Very common, low cost, good for engine blocks, pipes, machine bases
- Carbon steel, alloy steel: For structural parts, machinery components
- Stainless steel: Corrosion-resistant applications
- Aluminum: For lightweight parts, but die casting is usually better for high volume
- Brass, bronze: For bearings, valves, decorative parts
- Copper: For electrical applications
4.3 Sand Casting Advantages and Disadvantages
| Advantages | Disadvantages |
|---|---|
| Very low tooling cost (patterns are cheap) | Lower dimensional accuracy |
| Can make very large parts (tons) | Rougher surface finish |
| Almost any metal can be cast | More post-processing (machining, grinding) |
| Suitable for low volume and prototyping | Higher labor content per part |
| Design flexibility (easier to modify patterns) | Higher porosity compared to die casting |
| Widely available — foundries everywhere | More material waste (sprue, runners, risers) |
4.4 Typical Specifications
| Parameter | Typical Range |
|---|---|
| Minimum wall thickness | 3-6mm (depends on size and material) |
| Dimensional tolerance | ±0.5-1.0mm for small parts, ±1-3% for larger parts |
| Surface finish (as-cast) | Ra 12.5-50 μm (rough) |
| Part size range | A few grams to hundreds of tons |
| Tooling cost (pattern) | $200-5,000 (wood/foam), $2,000-15,000 (aluminum) |
| Tooling lead time | 1-3 weeks |
| Production rate | 10-1000 parts per week (varies widely) |
| Minimum order quantity | 1-100 parts |
4.5 Sand Casting in China
China has thousands of sand foundries, from small workshops to large automated foundries. Sand casting is widely available and very cost-competitive.
However, sand casting is one of the more polluting manufacturing processes (sand waste, air emissions, energy-intensive melting), and it has been heavily targeted by environmental enforcement in China. Many small foundries have been shut down or forced to upgrade their equipment.
Important: When sourcing sand castings from China, verify that the foundry has proper environmental permits and is not at risk of being shut down.
5. Other Casting Processes
5.1 Gravity Die Casting (Permanent Mold Casting)
Similar to die casting but metal is poured by gravity rather than injected under pressure. Uses a reusable metal mold.
- Materials: Aluminum, zinc, copper alloys
- Pros: Lower tooling cost than high-pressure die casting, better density than sand casting, good for medium volume
- Cons: Slower than die casting, less detail, thicker walls required
- Used for: Medium-volume parts where die casting tooling is too expensive
5.2 Centrifugal Casting
Molten metal is poured into a rotating mold, centrifugal force pushes the metal to the mold wall.
- Used for: Cylindrical parts — pipes, tubes, rings, sleeves, bearings
- Pros: Very dense, uniform material properties, good for large cylindrical parts
- Cons: Limited to symmetric shapes
5.3 Squeeze Casting / Semi-Solid Casting
Combines casting and forging — metal is solidified under high pressure.
- Pros: Very low porosity, excellent mechanical properties, near-net shape
- Cons: Higher cost, limited availability, specialized process
- Used for: High-performance automotive and aerospace parts
6. How to Choose the Right Casting Process
Choosing the right casting process depends on your part’s requirements, volume, and budget.
6.1 Decision Framework
| Factor | Die Casting | Investment Casting | Sand Casting |
|---|---|---|---|
| Volume | High (5,000+/year) | Medium (50-5,000/year) | Low (1-1,000/year) |
| Part size | Small-medium (under 50kg) | Small-medium (under 50kg) | Any size (up to tons) |
| Complexity | Medium-high | Very high | Low-medium |
| Dimensional accuracy | Excellent | Very good | Fair |
| Surface finish | Good | Very good | Poor |
| Material options | Non-ferrous only (Al, Zn, Mg) | Almost any metal | Almost any metal |
| Tooling cost | High | Medium | Low |
| Per-unit cost | Low (at volume) | Medium-high | Medium (at low volume) |
| Lead time to first parts | 6-10 weeks | 4-8 weeks | 2-4 weeks |
6.2 Common Scenarios
Scenario: Electronic enclosure, 100,000 units/year, aluminum → Die casting — high volume justifies tooling cost, good surface finish, excellent dimensional accuracy
Scenario: Stainless steel valve body, 2,000 units/year, complex internal passages → Investment casting — complex geometry, steel material, medium volume
Scenario: Large machine base, 50 units/year, cast iron → Sand casting — large part, low volume, low tooling cost, cast iron works well in sand
Scenario: Zinc connector housing, 500,000 units/year, very thin walls → Die casting (zinc) — very high volume, zinc has excellent castability for thin walls and fine detail
Scenario: Steel gear housing, 200 units/year, prototype phase → Investment casting or sand casting — low volume, steel material, investment casting for better accuracy, sand casting for lower cost
6.3 Hybrid Approaches
Many parts use a combination of casting and machining:
- Cast + machine: Cast the near-net shape, then machine critical surfaces and tolerances
- Die cast + CNC: Die cast the general shape, then CNC machine features that need tight tolerances
- Investment cast + finish grinding: Investment cast for complex shape, then grind for final surface finish
For most functional parts, some secondary machining is needed to achieve the tightest tolerances and best surface finishes.
7. Quality Considerations
7.1 Porosity
Porosity (small voids or gas pockets in the metal) is the most common casting quality issue.
Types of porosity:
- Gas porosity: Caused by gas trapped during pouring or injection. Small, spherical pores.
- Shrinkage porosity: Caused by metal shrinking as it solidifies. Irregular shape, often internal.
- Blowholes: Larger cavities caused by gas or steam from the mold material.
How to reduce porosity:
- Proper gating and venting design
- Controlled metal temperature and composition
- Proper mold temperature
- For die casting: proper injection parameters, vacuum assistance
- For investment casting: proper shell baking and dewaxing
- For sand casting: proper sand moisture content and venting
Testing for porosity:
- X-ray inspection (radiography)
- Ultrasonic testing
- Density measurement
- Sectioning and microscopic examination
7.2 Dimensional Accuracy
Cast parts have wider tolerances than machined parts. It is important to set realistic expectations:
| Process | Typical Tolerance |
|---|---|
| Die casting | ±0.05mm to ±0.2mm (depends on size and feature) |
| Investment casting | ±0.05mm to ±0.3mm |
| Sand casting | ±0.5mm to several millimeters |
Always specify critical dimensions that need tighter tolerances — those can be achieved with secondary machining.
7.3 Material Composition
Material composition is critical — it determines the mechanical properties, corrosion resistance, and performance of the part.
How to verify material:
- Require material test certificates from the foundry
- Do independent testing (spectrometer analysis)
- For critical parts, test every batch or every heat
- Include material composition specifications in your contract
7.4 Surface Defects
Common surface defects in castings:
- Cold shuts / cold laps: Metal flows meet but do not fuse properly
- Inclusions: Sand or slag particles embedded in the surface
- Flash / fins: Excess metal along parting lines
- Shrinkage cavities: Depressions on the surface from shrinkage
- Cracks: Hot tears or cold cracks
Most surface defects can be repaired (welding, grinding, polishing) but it adds cost and may affect structural integrity.
8. Working with Chinese Foundries
8.1 Finding Foundries
- Alibaba / Made-in-China: Good for initial search, but quality varies widely
- Industry trade shows: CastExpo, China Foundry Week
- Referrals: Best way to find quality foundries
- Local sourcing agents: Can help identify and vet foundries
8.2 Qualifying a Foundry
Facilities and equipment:
- What types of casting do they specialize in?
- What size and capacity are their furnaces?
- Do they have in-house machining?
- What quality control equipment do they have (spectrometer, X-ray, CMM)?
- Do they have proper environmental permits?
Capabilities:
- What materials do they work with?
- What is their typical part size range?
- What industries do they serve?
- Do they have engineering support for DFM?
- Can they handle secondary operations (machining, finishing, assembly)?
Quality systems:
- ISO 9001 certification (minimum)
- IATF 16949 for automotive
- Material testing capabilities
- Inspection procedures and records
8.3 Red Flags
- Very low prices that seem too good to be true
- Reluctance to provide material certifications
- No quality control equipment or procedures
- Poor communication or slow response
- Factory looks disorganized or dirty
- No environmental permits or history of violations
- Unwillingness to let you visit the facility
9. Key Takeaways
Casting is a versatile manufacturing process with options for every volume, material, and part size. China has the world’s largest casting industry, offering competitive pricing and a wide range of capabilities. The key to success is choosing the right casting process for your needs and finding a quality foundry.
Core principles:
- Choose the process based on volume and material. Die casting for high-volume non-ferrous, investment casting for complex/steel parts, sand casting for low-volume/large parts.
- Tooling cost vs. per-unit cost is the fundamental trade-off. Higher tooling investment = lower per-part cost at volume.
- Porosity is inherent to casting. Manage it with good design, process control, and testing.
- Set realistic tolerances. Cast parts are not as accurate as machined parts — use secondary machining for critical features.
- Verify material composition. Do not just trust the foundry’s word — test it.
- Environmental risk is real for foundries. Especially for sand casting and plating — verify permits and compliance.
- Quality foundries are worth paying for. Cheap foundries often cost more in rework, delays, and quality problems.
At Geason Law Offices, we help foreign hardware companies navigate Chinese manufacturing — from supplier qualification to quality agreements to dispute resolution. He Qianggao and our manufacturing team bring over a decade of experience to help you find the right suppliers, negotiate fair terms, and protect your interests.
FAQ
Q1: How do I protect my IP when manufacturing in China?
A1: Protecting IP in Chinese manufacturing requires a multi-layered approach: registering trademarks, patents, and copyrights in China (not just in your home country), executing comprehensive manufacturing agreements with clear IP ownership provisions and confidentiality clauses, implementing supply chain controls to prevent overproduction and gray market diversion, conducting regular factory audits, and registering IP with China Customs to prevent unauthorized exports. It’s also important to conduct thorough due diligence on manufacturing partners and to structure agreements with clear dispute resolution mechanisms, preferably with Chinese court jurisdiction or arbitration in China.
Q2: What quality control standards apply to manufactured goods in China?
A2: China has a comprehensive system of quality standards including national standards (GB), industry standards, local standards, and enterprise standards. For many consumer products, compliance with GB standards is mandatory. Products sold in China may also require CCC (China Compulsory Certification) marking depending on the product category. For export products, manufacturers must meet the standards of the destination country. China’s Product Quality Law establishes manufacturer liability for defective products, including compensation for damages caused by quality issues.
Q3: How does China’s environmental regulation affect manufacturing operations?
A3: China’s environmental regulations have become increasingly stringent, particularly under the Environmental Protection Law and the “Dual Carbon” goals. Manufacturing facilities must obtain environmental impact assessments (EIA) before construction, install pollution control equipment, meet emission standards, and participate in the emissions trading system for certain pollutants. Violation penalties have increased significantly and can include daily fines, production suspensions, and even criminal liability for serious environmental pollution incidents.
Q4: What are the key labor law requirements for manufacturing facilities in China?
A4: Manufacturing facilities in China must comply with comprehensive labor requirements including standard working hours (40 hours/week), overtime pay (150% on weekdays, 200% on rest days, 300% on statutory holidays), mandatory social insurance contributions (pension, medical, unemployment, work injury, maternity), written employment contracts within 30 days of hiring, and workplace safety standards under the Work Safety Law. For factories using dispatch workers, the total proportion of dispatched workers cannot exceed 10% of the total workforce.
Q5: What is the difference between OEM and ODM arrangements in China?
A5: OEM (Original Equipment Manufacturing) involves a foreign brand providing product specifications and designs to a Chinese factory that manufactures according to those exact specifications. ODM (Original Design Manufacturing) involves the Chinese factory both designing and manufacturing the product, with the foreign brand typically putting its own label on the finished product. The key legal differences relate to intellectual property ownership, liability for design defects, and the degree of control the brand has over the manufacturing process and quality standards.
Further Reading
- CNC Machining & Precision Parts Manufacturing in China: A Complete Guide — CNC machining
- Sheet Metal Fabrication in China: Processes, Materials, and Quality Considerations — Sheet metal
- Surface Treatment & Finishing Processes in China: A Guide for Hardware Products — Surface finishing
- Tooling Cost in China: A Complete Guide to Mold Pricing, Payment and Ownership — Tooling cost
Next Steps
Whether you are designing a new cast part or looking for a better foundry, understanding the different casting processes and their trade-offs will help you make better decisions.
Two service lines most relevant for casting and manufacturing:
- Commercial Contracts & Manufacturing Agreements — Quality and specification clauses
- Manufacturing Legal Support in China — Full manufacturing legal support
To discuss casting or any manufacturing legal matter, Contact Geason Law Offices. The initial consultation is free; the form prepares an email in your own mail application.
Related guides in this series
- Injection Molding in China: A Complete Guide for Hardware Startups
- Raw Material Sourcing in China: Managing Price Volatility and Supply Risks
- Quality Control in China Hardware: Inspection, Testing and Defect Prevention
Frequently Asked Questions↑ Back to article
What is the difference between die casting, investment casting, and sand casting?
The main differences are in tooling, cost, precision, and volume suitability. Die casting uses steel molds (dies) and injects molten metal under high pressure — very fast, high volume, excellent dimensional accuracy, but limited to non-ferrous metals (aluminum, zinc, magnesium). Investment casting (lost wax) uses wax patterns and ceramic shells — very high precision and complex geometries, wide range of metals, but slower and more expensive per part. Sand casting uses sand molds — lowest tooling cost, can make very large parts, widest range of metals, but lowest dimensional accuracy and rougher surface finish.
Which casting process is cheapest for high-volume production in China?
For high-volume production (10,000+ parts per year) of non-ferrous metal parts (aluminum, zinc, magnesium), die casting is usually the cheapest per unit. The tooling is expensive ($5,000-50,000+), but the per-part cost is very low because the process is fast and automated. For ferrous metals (steel, iron) at high volume, investment casting or sand casting with automated lines are used. For low volume, sand casting has the lowest tooling cost and may be cheapest overall.
What materials can be die cast in China?
Die casting is limited to non-ferrous metals with relatively low melting points. The most common die casting materials in China are: (1) Aluminum alloys — ADC12, A380, A356 — the most common, good strength-to-weight ratio, good corrosion resistance, (2) Zinc alloys — Zamak 3, Zamak 5 — very fluid, excellent detail, good for small parts and decorative features, (3) Magnesium alloys — AZ91D — very lightweight, good for structural parts, (4) Copper alloys — less common, higher melting point, more expensive. Steel and iron cannot be die cast because their melting temperature is too high for steel dies.
What is the typical lead time for casting tooling in China?
Tooling lead time varies by process: Die casting tooling — 3-6 weeks for simple parts, 6-10 weeks for complex parts. Investment casting tooling (wax injection dies) — 2-4 weeks. Sand casting tooling (patterns) — 1-3 weeks for wood patterns, 2-4 weeks for aluminum patterns. These are just tooling lead times — you also need to add sample testing and validation time (another 2-4 weeks) before production. Total time from order to first production parts is typically 6-12 weeks for die casting, 4-8 weeks for investment casting, and 3-6 weeks for sand casting.
What are common quality issues with cast parts from China?
Common casting quality issues include: (1) Porosity — gas pockets or shrinkage voids inside the part, which can weaken it or cause leaks, (2) Dimensional variation — cast parts have wider tolerances than machined parts, (3) Surface defects — cracks, cold shuts, inclusions, rough surfaces, (4) Flash — excess metal along parting lines that needs trimming, (5) Material issues — wrong alloy composition, impurities, (6) Draft angle problems — parts that stick in the mold or have uneven surfaces, (7) Warping — parts distort as they cool. Good foundries manage these through process control and inspection.
How do I choose the right casting process for my product in China?
The right casting process depends on your material, volume, precision requirements, and budget. For high-volume production of non-ferrous metals like aluminum or zinc, die casting offers the lowest per-unit cost and best precision but has high tooling costs. For complex geometries or ferrous metals at medium volume, investment casting provides excellent precision and surface finish at a higher per-part cost. For large parts, low volumes, or when cost is the primary concern, sand casting has the lowest tooling cost and widest material range but the lowest dimensional accuracy and roughest surface finish.
What are the main advantages and disadvantages of die casting in China?
Die casting offers very high production rates with fast cycle times, excellent dimensional accuracy and repeatability, good surface finish, the ability to produce thin walls and complex details, and low per-unit cost at high volume. The main disadvantages are high tooling cost ranging from $3,000 to $50,000 or more, limitation to non-ferrous metals only, unsuitability for low-volume production due to tooling amortisation, porosity concerns, and part size limitations typically under 50 kilograms for aluminum. Die casting quality in China ranges from world-class automated facilities to basic operations, so supplier selection is critical.